Tamko Gutter Replacement Nationwide

Tamko Gutter Replacement: The Jacksonville Owner’s Guide

Tamko gutter replacement in Jacksonville typically runs $9 to $18 per linear foot installed, which puts a standard 150-foot single-story home between $1,350 and $2,700 for a complete gutter system replacement. We stock Tamko-compatible aluminum and steel gutter profiles on our trucks, and most single-family homes are measured, quoted in writing, and completed within one day once materials are confirmed. You usually find out your gutters have failed the hard way: a hard Florida downpour sends water over the lip, down the fascia, and into the flower beds or pooling against the slab.

Call (904) 719-6346

This guide covers exactly what a Tamko gutter replacement involves here in Jacksonville: which profiles match your roofline, what fails on Florida homes, what a fair installed price looks like, and when it makes sense to call a crew instead of wrestling with an extension ladder on a Saturday.

Key Takeaways

• Installed cost for Tamko-compatible gutters in Jacksonville: $9 to $18 per linear foot, complete with hangers, end caps, outlets, and downspouts.
• Most Jacksonville homes need the half-round or K-style 5-inch profile, matched to existing fascia and roof pitch.
• Florida’s rainfall and humidity punish seams, hangers, and downspout connections faster than the gutter material itself.
• Every Brennan Roofing job comes with a written price before work starts and the 365-Day Done Right Promise in writing.

Which Tamko Models This Applies To

Tamko’s gutter and rain-removal product line runs primarily through their metal accessories division, with the most common residential profiles being the 5-inch K-style aluminum gutter and the 6-inch half-round steel profile used on higher-pitch roofs and some older Jacksonville ranch and bungalow styles. If you have Tamko gutters, look for the manufacturer stamp on the inside face of the gutter channel or on the end cap. If the stamp has worn off, which happens quickly in coastal air, measure the top opening across the gutter: 5 inches is the residential K-style standard, 6 inches is the commercial and steep-slope upgrade.

One compatibility gotcha we run into regularly: Tamko’s 5-inch K-style profile uses a slightly different lip geometry on the back edge than big-box off-the-shelf sections, which means a no-name replacement piece from a home center can leave a visible seam and a water channel that drips. We use Tamko-spec or direct-match aftermarket sections from the same gauge aluminum, not whatever is on the shelf. For most Jacksonville homeowners, the decision comes down to this: OEM Tamko sections when the roofline still has original gutter and we’re matching, and quality aftermarket 0.032-gauge aluminum when the whole run needs replacing anyway. The material difference at that gauge is negligible; the install quality is not.

Signs Your Tamko Gutter Replacement Is Failing

• Water pouring over the gutter lip during normal rain. This means the pitch is wrong or the hangers have pulled loose, and the gutters can’t carry water to the downspout. In Jacksonville, a 1-inch-per-hour downpour will expose this in about ten minutes.
• Fascia board staining or peeling paint directly below the gutter line. Water is getting behind the gutter, either from a broken end cap seam or a gap between the back lip and fascia board.
• Rusted-through seams or pinhole leaks in the bottom channel. Steel gutters in humid Florida air rust from the inside out. By the time you see rust on the outside, the channel is already compromised.
• Water pooling around the foundation or slab after storms. This means the downspout is disconnected, undersized, or draining too close to the house. Jacksonville’s high water table makes this a foundation concern, not just a landscaping nuisance.
• Gutters visibly pulling away from the roof edge or sagging between hangers. Hanger failure. Once one section drops, every downpour adds weight and the problem accelerates.

Replacement Cost & What’s Included

A full Tamko-compatible gutter replacement in Jacksonville runs $9 to $18 per linear foot installed. A smaller single-story ranch in Mandarin or Arlington might run 120 linear feet and land around $1,200 to $1,800. A larger two-story home in San Marco or Ortega with 200-plus linear feet and custom downspout runs can push $2,800 to $3,800.

The price on our written estimate includes removal and haul-away of the old gutter, new hangers and fasteners, downspouts and elbows, and a final flow test with a garden hose before we pack up. What drives the range: the linear footage, the number of corners and downspouts, whether we need to repair or replace rotted fascia board first, and whether the roof edge needs a drip edge added. Our price goes on paper before any work starts, and it does not move at the door.

DIY or Call Us?

What you can safely do yourself: clear debris from the channel, confirm the downspout is attached and draining, and mark where water is spilling over with tape so you can show us exactly what you’re seeing. That kind of eyeball report saves time on the estimate.

What goes wrong when homeowners attempt the replacement themselves: gutter runs over 20 feet need proper pitch (about a quarter inch per 10 feet), and each splice has to be sealed with gutter-specific sealant or it leaks at the first hard rain. Working off an extension ladder while handling 10-foot gutter sections in Jacksonville wind is genuinely dangerous, and a crooked run of gutter looks worse than the one you’re replacing. This is where our crew earns the money. Travis Oakley has spent the better part of two decades running jobs up and down the Florida coast, and he’ll tell you the same thing he tells the youth baseball team he coaches: shortcuts show up eventually. If it’s not right, we’re not done. Call (904) 719-6346 for a free estimate with a written price before any work starts.

FAQs