IKO Gutter Replacement Nationwide

IKO Gutter Replacement: The Jacksonville Owner’s Guide

IKO gutter replacement in Jacksonville typically runs $8 to $14 per linear foot installed for standard 5-inch aluminum gutters, with most single-story homes landing between $1,100 and $2,400 for a full replacement. We stock IKO-compatible profiles on our trucks and can usually complete a full gutter swap in one day. Most Jacksonville homeowners discover they need this work after a hard afternoon thunderstorm, when water pours over the gutter face instead of flowing to the downspout, or when a section pulls away from the fascia and hangs at a visible angle.

Call (904) 719-6346

Which IKO Models This Applies To

IKO manufactures two gutter lines that matter for replacement in Jacksonville: the standard 5-inch K-style profile and the 6-inch version used on homes with steep roof pitches or heavy tree cover. The 5-inch is the default on most single-family homes built since the 1990s. The 6-inch moves roughly 40% more water and is what we recommend for Jacksonville homes with mature oak canopies, which describe most neighborhoods from Riverside to Mandarin.

Identifying what you have is straightforward. Look inside the gutter along its top edge for an embossed manufacturer mark, or measure across the top opening. If it reads 5 inches, it’s the standard profile. If it reads 6, it’s the larger commercial-style run. The critical gotcha: IKO’s hanger spacing spec is 24 inches on center, but many original installs we see across Jacksonville use 32 to 36 inches. That gap is why gutters sag and pull away after a few hurricane seasons. We correct hanger spacing on every replacement, regardless of what the original installer did.

For replacements, we install either OEM IKO gutter profiles or 0.032-gauge aluminum aftermarket equivalents that match the existing profile. OEM is the right call when you’re replacing a damaged section and want a seamless visual match. Quality aftermarket is the better value when you’re doing the full run and want a heavier gauge than original spec. We’ll show you both options with the price difference on paper, before any work starts.

Signs Your IKO Gutter Replacement Is Failing

• Water spilling over the front edge during rain. This usually means the gutter is undersized for the roof area, the downspouts are clogged, or the pitch has flattened over time. In Jacksonville’s afternoon downpours, a 5-inch gutter that can’t keep up will overflow every time.
• Sagging sections or visible gaps between the gutter and fascia. The hangers have pulled loose, often because they were spaced too far apart originally. We see this constantly on older Jacksonville homes where the original install skipped proper spacing.
• Rust streaks or pinhole leaks along the bottom. Aluminum doesn’t rust, but steel fasteners and end caps do. Pinholes develop where standing water sits, usually at low spots where the pitch has shifted.
• Water pooling near the foundation or staining on the soffit. The gutter is moving water, but not to the downspout. That water ends up against the slab or wicking into fascia board, which is a much more expensive fix if ignored.
• Visible pulling at the mitered corners or separated seams. Heat expansion and contraction over a decade of Florida summers stress the corner joints first. Once a corner separates, the whole run loses tension and the problem spreads.

Replacement Cost & What’s Included

Installed IKO-compatible gutter replacement in Jacksonville runs $8 to $14 per linear foot for 5-inch aluminum, including removal of the old run, new hangers at proper spacing, downspouts, and end caps. A 6-inch upgrade adds $2 to $4 per foot. A typical 1,800 square foot single-story home with 160 linear feet of gutter lands between $1,300 and $2,000. Homes with complicated rooflines, second stories, or custom colors fall at the higher end.

What drives price: linear footage, gutter width, downspout count, whether fascia repair is needed behind the gutter, and how easy the roof edge is to access. We don’t quote a flat number and then move it at the door. The price goes on paper before any work starts, and it does not change unless you change the scope. Every replacement carries the 365-Day Done Right Promise: if it’s not right, we’re not done, and we come back at no charge for a full year if anything fails.

DIY or Call Us?

You can safely inspect your gutters from the ground. Look for visible sag, gaps at the fascia, water staining on the soffit, and whether water exits cleanly through the downspout during a storm. You can also clear debris from the gutter bed with a hose and gloves if you’re comfortable on a ladder.

What we don’t recommend is replacing gutter runs yourself. The work requires working at roof edge height, handling long aluminum sections that warp and kink if supported wrong, and getting the pitch right, which is measured in fractions of an inch per foot and is the difference between a gutter that drains and one that holds water. A gutter that holds water in a Florida summer breeds mosquitoes and rots the fascia behind it. If you want the job done once with the number in writing before we start, call (904) 719-6346 and we’ll come measure.

FAQs